___________________________________________________ ___________________________________________________ ________________________ 1 of 2 sl power electronics corp ? 6050 king drive ventura, ca 93003 ? phone 805.486.4565 ? fax 858.712.2040 ? email: info@slpower.com ? www.slpower.com CINT1150 150w single output series 3 years warranty ite power supply international safety agency approvals rohs specifications all specifications are typical at nominal input, fu ll load at 25 c unless otherwise stated . ac input 100-240vac +/- 10%, 47-63 hz single phase 120-370 vdc turn on time less than 2 sec. @115vac (inversely proportional to inpu t voltage and thermistor temperature) input current 115vac: 2a, 230vac: 1a hold - up time >12msec at full load and 120vac inrush current 264vac, cold start: will not exceed 50a signals ac power fail/dc ok input fuse s f1, f2: 4a, 250vac fuses provided on all models overload protection hiccup mode earth leakage curre nt <750 a@264vac, 60hz, nc short circuit protection no damage to the supply efficiency 88% typical at 115v pfc switching frequency 65khz typical output power 150w continuous with 200lfm airflow, 100w convectio n cooled ? see chart f or specific voltage model ratings overvoltage protection ovp firing reduces output voltage to <50% of nomina l in <50ms. see chart for trip range transient response 50% load step. i/ t <0.2a/s max volt deviation = 3% isolation input-output: 4000vac input-ground: 1 800vac, output-ground: 500vac ripple and noise see chart operating temperature -10 to +70 c derate output power linearly to 50% at 70 c output voltage see chart storage temperature -40 to +85 c voltage adjustability +/- 5% from nominal operating altitude -500 to 10,000 ft (approved to 3,000m) minimum load not required non - operating altitud e -500 to 40,000 ft total regulation +/- 5%. see chart relative humidity 5% to 95%, non-condensing vibration operating: 0.003g 2 /hz, 1.5g rms overall, 3 axes, 10 min/axis non-operating: 0.026 g 2 /hz, 5.0g rms overall, 3 axes, 1 hr/axis shock operating: half-sine, 20 g pk , 10 ms, 3 axes, 6 shocks total non-operating: half-sine, 40 g pk , 10 ms, 3 axes, 6 shocks total dimensions w: 2.0? x l: 4.0? x h: 1.3?. weight: 183g ite safety standards en/csa/ul/iec 60950-1, 2nd edition ? 2? x 4? x 1.3? package ? for 1u applications ? 150watts with air & 100watts convection cooled ? universal input 90-264 vac ? approved to en/iec/ul60950-1 2nd edition ? power fail/output good signal ? compliant (lvd, rohs) ? optional chassis/cover product fam ily: "k" = 3 pin header, class i input "06" = output connector - 6 pin header "12" = 12vdc, "24" = 24vdc, etc. "a" = first generation "150" = 150 watts output pow er "1" = single output "c" = ite/industrial, "i" = internal, "nt" = new te chnology input connector: output connector: output voltage: configuration: output pow er: # of outputs: 1 150 x k model: "01" = standard model, 02 and higher indicates a m odified m odel. model number key 12 06 cint 01 www.datasheet.net/ datasheet pdf - http://www..co.kr/
___________________________________________________ ___________________________________________________ ________________________ 2 of 2 sl power electronics corp ? 6050 king drive ventura, ca 93003 ? phone 805.486.4565 ? fax 858.712.2040 ? email: info@slpower.com ? www.slpower.com CINT1150 150w single output series 3 years warranty ite power supply models & output parameters model number volts (v) convection 1 with 200lfm air ripple & noise 2 total regulation ovp threshold CINT1150a1206k01 12v 8.33a 12.50a 0.5%rms, 1.2% pk-pk 5% 14.0 1.1v CINT1150a2406k01 24v 4.17a 6.25a 0.5%rms, 1% pk-pk 5% 28.0 2.5v CINT1150a4806k01 48v 2.08a 3.13a 0.5%rms, 1% pk-pk 5% 55.0 4.0v CINT1150a5606k01 56v 1.79a 2.68a 0.5%rms, 1% pk-pk 5% <59.9v notes: 1. maximum output power is 95 watts for inp ut voltage of 90-105vac at 50 c convection. for input voltage of 105vac or more, th e total power is 100 watts at 50 c convection. 2. measured with noise probe directly across o utput terminals, and load terminated with 0.1f cer amic and 10f low esr capacitors. emc compliance conducted emissions en55011/22 class b, fcc part 15, subpart b, class b radiated emissions en55011/22 & fcc part 15, subpart b, class a with 6db margin static discharge immunity en61000-4-2, criteria a, 6kv contact discharge, 8kv air discharge radiated rf immunity en61000-4-3, 3v/m. criteria a eft/burst immunity en61000-4-4, 2kv/5khz, criteria a line surge immunity en61000-4-5, 1kv differential, 2kv common-mode, cri teria a conducted rf immunity en61000-4-6, 3vrms, criteria a power frequency magnetic field immunity en61000-4-8, 3a/m, criteria a voltage dip immunity en61000-4-11, loading is 70% of 100 watts with 100 vac input. 0% vnominal, 0.5cycle, 40% vnominal, 5 cycles, 70% vnominal, 25 cycles, criteria a. line harmonic emissions en61000-3-2, class a, b, c & d flicker test en61000-3-3, complies (dmax<6%) signals ac power fail /dc ok: during normal operations stays high power fail: goes low wi th 5 ms warning before loss of output power due to ac fa ilure dc ok: open collector logic signal goes and stays high 100ms ? 500ms after dc output reaches regulation mechanical drawing and input/output connections data sheet ? 2012 sl power electronics corp. the i nformation and specifications contained herein are believed to be correct at the time of publication. rev. 9/25/2012 however, sl power accepts no responsibility for con sequences arising from reproduction errors or inacc uracies. specifications are subject to change with out notice. input connector (j100): pin 1) ac line pin 2) empty pin 3) ac neutral mating conn: ground (j101) fg 0.187" faston tab mating conn: dc output connector (j200): pin 1) +vout pin 4) -vout pin 2) +vout pin 5) -vout pin 3) +vout pin 6) -vout mating conn: signal connector (j300): pin 1) pf/dcok pin 2) common mating conn: molex 09-50-3031, pins = 08-52-0072 molex 01-90020001 amp 640250-6, pins = 640252-1 molex 1375820-2, pins = 1375819 www.datasheet.net/ datasheet pdf - http://www..co.kr/
|
